TRED GT Leveling Ramp - Gun Grey

Video Transcript for Review of Rhino Rack - TRED GT Levelling Ramp - RR84AP

Hello, everybody. This is Jeff at etrailer.com. Today, we're gonna take a look at this TRED GT Leveling Ramp. It's for a quantity of one ramp. Now, this TRED GT Leveling Ramp has been engineered to keep your vehicle or trailer secure and level. This part here is for a quantity of one.

These are usually designed to be used together in pairs, and it is a TRED-link design, so basically it'll allow you to nest all the components together in one part for a nice easy grab-and-go convenience. Now, this ramp is normally used with the TRED GT Wheel Chock, which is not included. We do sell that separate on our website. It's part number RR44AP, and I happen to pull one of those just so you can see what we're talking about. And then, basically, the way it nests together is it'll go right on the front here.

You just put it down here and then slide it over. And once you get it slid in position, you can see now it's set up and you're ready to roll the tire up on here. You can see the honeycomb design here on the top of the ramp, gives its superior strength. It's rated for 5,000 kilograms, which is a little over 11,000 pounds. The bottom of the ramp is a full flat surface that helps support the vehicle or trailer on soft surfaces.

And just to demonstrate this wheel chock that it doesn't come with, you do have to buy that separately. But just to show you, I wanted to show you how this works. Basically, you roll your tire up on here, the tire would hit this and sort of stop and put it in the right position, and then a nice feature about it is once it's installed,, you can just slide this off from underneath the tire and remove it. And then with your tire up there, you use it as a chock. All you gotta do is put it behind the tire, and then just ratchet or slide it up.

And when you get it right under the tire, let it go, and it'll slide down and then lock in place. You notice on the top of the ramp, it has these hooks on it going in one direction, so when you put your chock on there, you can ratchet it by pushing it up. Then when you get under the tire and you let it go, it'll slide back down and lock onto those hooks. So, the chock will be used in that position. Also, what's nice is if you notice on each end of the chock, it has these attachment points you can attach a strap to and that'll allow you to, when it's in your position, just pull on either side with the strap and it'll slide right out from under the tire. And then you just install it back onto the front just like that again. Now, the ramp itself is gonna give you 4-1/2" of lift, and that's from the bottom to the very top right here. The shorter length of this ramp allows it to fit in between some of the larger size off-road tires that are out there on some tandem-axle setups. The ramp length from here to here is 14-1/2", and that's with the chock removed. The ramp dimension we mentioned 4-1/2" tall, the width 9-3/4" wide, the ramp length we said is 14-1/2", and the base length of the whole unit end-to-end is 16-1/2". And we mentioned that TRED length design where the chock hooks in here. I do wanna also show you a popular product we sell is the Leveling Pack. And what the Leveling Pack is, it allows you to nest all the components together in one part of, make it easy, grab and go convenience. Just to show you that pack, we sell it separately, but I wanted to show it to you. This is it here, it only weighs about 12 pounds, but basically what it includes, goes by a part number of RR74AP. But basically if you notice, it includes the two ramps locked together, the two chocks, one on this end, one on this end, and then the sink plates are the jack plates, two up here and two down here. So you get two ramps, two chocks, and then four jack plates. All comes as one pack, but again, that's sold separately. But that should do it for the review on this TRED GT Leveling Ramp, quantity of one.